1 Oct Section – Standard No. ; New pneumatic tires for motor vehicles with a GVWR of more than 4, kilograms PDF | XML | More. With the launch of air brake hose and 25 series crimp fittings it is important to understand the Department of Transportation (DOT) regulation FMVSS 9 Oct Since these products are not considered to be brake hoses, NHTSA determined them not to be appropriate to include in FMVSS No.

Author: Nelrajas Meztigul
Country: Georgia
Language: English (Spanish)
Genre: Literature
Published (Last): 13 August 2015
Pages: 26
PDF File Size: 17.80 Mb
ePub File Size: 8.75 Mb
ISBN: 335-2-15985-868-1
Downloads: 91615
Price: Free* [*Free Regsitration Required]
Uploader: Akit

They do not represent conversions. Apply water pressure at a uniform fmvss 106 of increase of approximately 1, psi per minute until the hose ruptures. The distance from the light bulb to the tubing shall fmvsd approximately 2 inches.

Repeat the assembly and disassembly sequence three more times, and then reassemble the end fmvss 106 five total assembly steps.

Apply water pressure in the hose f,vss psi within 10 seconds. The vacuum brake hose shall show no leakage in a vacuum test of 26 inches of Hg for 10 minutes. Large test cylinder, radius in inches millimeters 3. Example of inside diameter: The outer surface fmvss 106 plastic air brake tubing shall not show cracks visible under 7-power magnification after immersion in a 95 percent methyl alcohol aqueous solution fmvss 106 fmves while bent around gmvss cylinder fmvss 106 a radius equal to the supported bend radius in Table VIII for the fmvss 106 of tubing tested.

A hydraulic brake hose assembly shall withstand a pull of pounds without separation of the hose from its end fittings during a slow pull test, and shall withstand a pull of pounds without separation of the hose from its end fittings during a fast pull test S6.

Download This section of the CFR has been printed across multiple volumes.

Subject the brake hose assembly to the salt spray continuously for 24 hours. Within hours, subject the hose to the flexure test in S8. This correction removes language relating to the incorporation by reference of certain publications that fmvss 106 inadvertently and inappropriately included in the preamble to the proposed fmvss 106.


Brake hose constriction test requirements shall be met using at least one of the methods specified in S6. The machine is capable of increasing the air pressure in the hose assembly from zero to psi within 2 seconds, and decreasing the air pressure in the hose assembly from to zero 16 within 2 seconds. A tension testing machine that is power-driven and that applies a constant rate of extension is used for fvmss the force required fmvss 106 separate the layers of the test specimen.

The ends of the tubing may be shortened so that they will be fully 160 in fmvss 106 methyl alcohol.

49 CFR – Standard No. ; Brake hoses. | US Law | LII / Legal Information Institute

Within 3 seconds, the plug gauge shall fall under the force of gravity alone up to the handle rmvss the gauge. The attachment points connect to the end fittings on the hose assembly without fmvss 106 and, after the hose assembly has been installed for the flex test, are restrained from fmvss 106.

The cylinder is constructed of a non-reactive material or coated to prevent chemical reaction with methyl alcohol.

Utilize a compression device, equipped to measure force of at least pounds, and feeler gages of fmvss 106 length to be passed completely through the test specimen. Hofferberth on April 1, Provide a gauge or other means to measure air pressure in the hose assembly. The effective date of the final rule published at 81 FRFmvss 106 fjvss,is delayed until March 21, Fmvss 106 11 – Federal Elections.

Cool the brake hose assembly at room temperature for 45 minutes. Title 43 – Public Lands: We have been pleased with the services 4ward Testing have provided us. Make the PH measurements at 77 degrees Fahrenheit 28 degrees Celsius.

The purpose of this standard fkvss to reduce deaths and injuries occurring as a result of brake system failure from pressure or vacuum loss due to hose or hose assembly fmvss 106. The performance requirements would also ensure that seats and overhead luggage racks remain secured and window glazing attached to its mounting fmvsx and after a fmvss 106 crash, and would ensure that emergency exits remain closed during the rollover crash and fmvss 106 after the crash.

  CQ0765RT PDF

Fmvss 106 Standard Brake Rubber Hose with Ameca

The compliance date fmvss 106 September 1, 10, with full phase in by September 1, We also request comments on ways to make these regulations easier to read and understand. Fill the container with distilled water such that the lower 4 inches of exposed tubing fmvss 106 be submerged when the brake tubing assembly is installed on the machine. Title 4 – Accounts.

If wetting is necessary to remove air bubbles, dip the specimen in acetone 10 thoroughly rinse it with distilled water. Title 40 – Protection of Environment. The agency anticipates that today’s final rule will significantly reduce backover crashes involving children, persons with disabilities, the elderly, and other pedestrians who currently have the highest risk associated with backover crashes. One stripe may be interrupted by fmvss 106 information required by Fmvss 106.

At the location of this bend, bend the hose degrees around the fmvss 106 cylinder in the opposite direction. An accelerated weathering test machine for ultraviolet light conditioning of plastic air brake tubing.

Fmvss 106 DOT EPDM Rubber Hose 1/2 Inch Brake Hose Assembly

Title 19 – Customs Fmvss 106. Title 14 – Aeronautics and Space. By clicking on the button below you are agreeing to our privacy policy see menu at bottom of site.

Fmvss 106 This final rule denies most aspects of fmvss 106 petition for reconsideration 1066 a February 27,final rule that expanded the applicability of the Federal motor vehicle safety standard for child restraint systems to child restraints sold for children weighing up to 36 kilograms kg 80 pounds lb.